How to make a straight beginning row
| Table of contents |
|---|
| 1 - A small bracelet 2 - A large bracelet 3 - Two buckles |
as requested by Melancholy :-)
One quick and easy way to make an even, straight line at the very beginning of any bracelet would be, of course, to cut single threads and tape them down in the correct order. But it works just as nicely when you're starting with a buckle - and the first step, naturally, is to make the buckle. The tutorial can be found here: https://www.friendship-bracelets.net/tutorial.php?id=370
Depending on how many threads your bracelet has, you'll want to create a bigger/wider buckle. For any pattern with more than 40 threads it would be a wise move to make two buckles.
A small bracelet
I've chosen to make #3649, which has 18 threads. When it's done it will be 1.8 cm wide, or 0.7 in - so the buckle needs to be no longer than 3 cm (1.2 in) and I'll fold it so it forms a fairly narrow loop.
To make sure the starting row not only gives the knotted part an even beginning, but to also ensure that the buckle stays centred, I like starting with the middle knot. I've created some extra order and fanned out the threads, and organised them into groups of two, according to the thread order supplied by the pattern.
The first knot can look a little wonky, but those loose looking threads will even out as soon as more knots are added to either side. So, moving out from the centre, we'll take the adjacent pairs to make one knot on either side of the middle one.
It's still looking a little loose and messy right now, but this is about to change ;-) Since the pattern starts off with a chevron, I'll keep going with those threads I just used, until I reach the centre.
I'll do the same for the next thread - since the threads aren't exactly in the proper order, make very careful knots. The very first one often turns out a tad loose, but as of the second knot you can carefully establish nice, even tension. Just go slow and don't pull too tightly, and knot all the way down to the centre. Repeat on the other side.
That doesn't look half bad ;-) If it looks like it's turning out a bit uneven, or a bit off-centre, give the threads a gentle little tug to smooth things out. This is another reason you don't want to make super tight knots, because you've left yourself some room for gentle tweaking :-)
Repeat this with the remaining two pairs on either sides - a careful, loose knot over the first thread to not create any unnecessary strain, and even knots towards the centre. Done!
A large bracelet
If you're making a bigger pattern, the approach is pretty much the same, but you'll have to allow for a wider buckle to have room for all the threads. I chose #7580, which has 32 threads and measures approx. 3 cm (1.2 in).
Because there are so many threads, the loop will have to extend a bit wider than with the previous bracelet, and I'll make the buckle at least 3.5 cm (1.4 in) long. When pinning it down, make sure it spans about 2 cm (0.8 in). With a bracelet this size I'll cheat a little and pin it on graph paper so I can make REALLY sure it's even all the way :-)
The pattern I've chosen is made up of two separate chevrons, and uses the same number of colours and threads on both sides. So I'll start on one side of the pattern, and leave the other side for later.
I've spread out the threads in the order I'll be using them, so they're as untangled as they can be, coming from inside the buckle.
I'll start at the centre again; in this case the centre isn't only one knot, but a mini-chevron of three knots. The other threads seem to be in the way (what's the light green doing there, hanging over like that?) but that's only temporary :-)
Moving on to the next pair of threads, I'll make a very careful knot - if I pull too tightly that will just put extra strain on the other threads. Note how the purple on the right side had to go OVER the dark green, and use the light green that seemed to be at a very awkward position. By making a very gentle, and rather loose knot, I've avoided the whole thing buckling in on itself.
I'll repeat the process for the remaining two pairs, paying extra attention to the very first knots. By keeping those fairly loose you'll automatically be creating a horizontal line. (I've pinned down the centre to keep it from moving, in case anyone's wondering what that extra pin's doing there.)
The left side is done, so I'll basically do the same thing on the right side. If anything, the threads seem to be in an even bigger mess than they were on the left - light green once again is not very co-operative, and this time purples's joining in the fun as well.
But I'll be starting in the centre anyway, and once again I'll be making that small chevron consisting of three careful knots.
Using the rebellious light green and purple, I'll have to be even more careful than usual. Because the threads were in such weird positions this doesn't look nearly as neat as the left side did...
Moving on to the next pair, it's time to fix what purple tried to mess up. Note how the first purple knot on the right is slanting down and trying to ruin my horizontal line? By making the first knot with the pink just that tad looser, we're on the way of fixing that.
By the time I'm onto the final pair, we're back where we want to be - in a nice, horizontal line. Now all that's left to do is to join both sides up :-)
Two buckles
If you don't like starting with one big buckle, you can, of course, make two :-)
Go about choosing your pattern like you would if you were making one buckle, but consider one more thing: Make sure there are at least two of each colour on either side of the pattern.
Here are a few examples, just in case this makes no sense:
Pattern #888 has 24 threads, consisting of two identical sides of 12 threads. So it's not only symmetrical, but as far as the threads are concerned, it's doubled side by side (two patterns #28 actually!), and ideal for two buckles.
The same holds true for pattern #54887: both sides are identical, and there are at least two of each colour on both sides.
See Allkoo's photo.
However, #48334 would be a lot easier to make with just one buckle. It's symmetrical, but the threads differ on both sides of the pattern. So if you were to half it to make two buckles, you'd end up with single threads for C, D, and E.
Alrightie, enough talk.
I'm making Arismende's gorgeous pattern #53249, which has 28 threads, consisting of two identical sides with 14 threads.
For a change I made a different buckle, just to try something new. The tutorial I used can be found here
Make the buckle for one half of the pattern, and follow the instructions from this tutorial to make a straight beginning.
Make the buckle on the other half of the pattern, and pin it next to the first. Start knotting this side of the pattern the same way you did on the left side.
Quick tension check! If you intially pinned the two buckles too far apart, or too close together, just shift one of them so both sides connect smoothly. A gap would cause the knots in the middle of the pattern to stretch and look loose, and if the buckles are too close together the knots will be fighting for room and make the centre look too tight, and make the pattern look uneven :-)
If you're happy with the position of your buckles, all you have to do now is connect the two sides. In this case all it takes is one little orange knot:
There, that's all there is to it :-)
Keep knotting, and when you're done, just finish off with two braids for each buckle for easier tying.
Done!
Editors
The original author of this tutorial is Foz .
Comments